Top-Lieferant 10 Jahre sind spezialisiert auf maßgeschneiderte Edelstahl Tischbeine , dekorieren trim und Wand-Bildschirm .
Über uns | Seitenverzeichnis | Kontakt
Englishالعربية中文(简体)FrançaisDeutschItaliano한국어PortuguêsРусскийEspañol
 Bearbeiten Übersetzung

Probleme und Gegenmaßnahmen im Prozess des Edelstahl Schleif

» NACHRICHTEN » Problems and countermeasures in the process of stainless steel grinding

Probleme und Gegenmaßnahmen im Prozess des Edelstahl Schleif

Kann 22, 2019

In order to meet the requirements of surface quality and machining accuracy of stainless steel parts, grinding method is usually adopted. Due to the high toughness, low thermal conductivity and small elastic modulus of stainless steel, the following problems often exist in the grinding process :1) the grinding wheel is easy to stick and block; 2) the processed surface is easy to burn; 3) serious machining hardening; 4) the workpiece is easy to deform.

From the above we can see that the choice of grinding wheel and grinding fluid directly affects the grinding efficiency and machining accuracy. The factors affecting adhesion blockage and surface roughness were studied experimentally.

Influence of grinding wheel size on adhesion rate.

The selected four grinding wheels of white corundum, hardness K and particle size 36, 46, 60 und 80 respectively were used for cylindrical longitudinal grinding of the specimen. The grinding length was 600mm and the adhesion rate was detected. The finer the grinding wheel, the more serious the adhesion. jedoch, the finer the grinding wheel is, the smaller the cavity will be. The grinding wheel will soon lose the chip space, causing blockage.

Effect of hardness of grinding wheel on adhesion rate.

The grinding wheels of white corundum with particle size 46 and hardness of H, J, K and L were selected to grind the specimens. The grinding stroke was 600mm and the adhesion rate was tested. The higher the hardness of the grinding wheel, the more serious the adhesion. This is because of the low hardness of the grinding wheel, grinding particles in the grinding force, easy to fall off from the surface of the grinding wheel, forming a new chip space, not easy to plug.

The influence of abrasive on the adhesion rate.

There are two kinds of common grinding wheel abrasives: white corundum and green silicon carbide. The experiment shows that the two kinds of abrasives have little difference on the adhesion rate.

Effect of grinding fluid on surface roughness.

Three kinds of emulsions, anorganisches Salz und Flüssigkeit auf Ölbasis Schleifflüssigkeit wurde jeweils verwendeten Schleif. Schwefel, Chlor und andere Extremdruckadditive zugesetzt, um die Oberflächenrauhigkeit des Werkstücks nach der Verarbeitung zu beobachten,. Die Strömungsgeschwindigkeit der Flüssigkeit betrug Schleif 20L / min und die Schleifhub war 600mm.

Es ist ersichtlich, dass die Oberflächenspannung klein ist, enthaltenden Höchstdruckadditive, die Oberflächenqualität durch Schleifen erhalten ist gut. Angemessene Verwendung von Schleifflüssigkeit, kann die Wärmeableitungsbedingungen verbessern, Fluidschleifen können Chips und aus den Schleifpartikeln mahlen, zur gleichen Zeit in der Metalloberfläche einen Ölfilm zu bilden,, Schmierung, das Werkstück Oberflächenrauigkeit verringern.

Wirkung der Schleif Dosierung auf Adhäsionsrate.

Wie aus der Tabelle ersichtlich, 1 und 2, die Änderung der Schleiftiefe hat wenig Einfluss auf die Haftrate.

Endlich, wir bekommen:

Beim Schleifen von Edelstahl, die Haftung Block Schleifscheibe zu reduzieren, ist ein wichtiger Faktor zur Verbesserung der Mahleffizienz.

2) grinding stainless steel grinding wheel is the main target of self-sharpening good grinding wheel, generally choose low hardness grinding wheel effect is good, but also can not choose the hardness is too low, otherwise the grinding particles will fall off. Grade J is recommended.

3) in order to reduce the adhesion block of grinding wheel during grinding, coarse-grained grinding wheel should be selected. Coarse grinding with 36, 46 particle size, fine grinding with 60 particle size.

4) GC wheel can improve grinding efficiency when grinding stainless steel.

5) grinding fluid selection must take into account both lubrication and cleaning, sufficient supply, can choose small surface tension, emulsion containing extreme pressure additives, can get high surface quality.

6) the selection of grinding amount can be determined according to the machining allowance.

7) during the experiment, it was found that the structure of the grinding wheel and the bonding agent had a certain impact on the grinding process of stainless steel. Currently, it is limited by the experimental means, which needs to be further studied.

Vielleicht gefällt Ihnen auch